ABSTRACT
Introduction: The purpose of this study was to evaluate the effectiveness and compare the accuracy of pulp tests in the diagnosis of teeth pulpal health. Material and Methods: Traumatized (n=71) and non-traumatized (n=71) teeth from 42 patients were evaluated. Each tooth underwent cold, heat, electric and oximetry tests, followed by radiographic examination and calculation of the sensitivity, specificity, PPV, NPV and accuracy. Results: Clinical and radiographic examination showed no alteration for the 71 teeth from the intact contralateral group. From the traumatized group, 29 teeth presented complete endodontic treatment, 17 presented periapical alterations that required endodontic treatment and 25 teeth did not present conclusive radiographic alteration. The cold test showed a significantly higher proportion of correct results, while the electric test showed a significantly lower proportion. The data showed higher accuracy for the cold, followed by oximeter and heat tests, while the electric test presented the lowest accuracy. Cold and oximeter tests proved superior over the electric and heat tests, while the electric test showed better parameters when diagnosing diseased pulp. Conclusion: Combining two pulp tests seems reasonable for improving the pulp diagnoses using both oximeter and cold or oximeter and heat tests to detect healthy pulp; or cold and electric tests to define diseased pulp.
Introducción: El propósito de este estudio fue evaluar la efectividad y comparar la precisión de las pruebas pulpares en el diagnóstico de la salud pulpar de los dientes. Material y Métodos: Se evaluaron dientes traumatizados (n=71) y no traumatizados (n=71) de 42 pacientes. Cada diente se sometió a pruebas de frío, calor, eléctricas y de oximetría, seguidas de examen radiográfico y cálculo de la sensibilidad, especificidad, VPP, VPN y precisión. Resultados: El examen clínico y radiográfico no mostró alteración en los 71 dientes del grupo contralateral intacto. Del grupo traumatizado, 29 dientes presentaron tratamiento endodóntico completo, 17 presentaron alteraciones peri-apicales que requirieron tratamiento endodóntico y 25 dientes no presentaron alteración radiográfica concluyente. La prueba en frío mostró una proporción significativamente mayor de resultados correctos, mientras que la prueba eléctrica mostró una proporción significativamente menor. Los datos mostraron mayor precisión para la prueba de frío, seguida de las pruebas de oxímetro y calor, mientras que la prueba eléctrica presentó la menor precisión. Las pruebas de frío y oxímetro demostraron ser superiores a las pruebas eléctricas y de calor, mientras que la prueba eléctrica mostró mejores parámetros al momento de diagnosticar pulpa enferma. Conclusión: La combinación de dos pruebas pulpares parece razonable para mejorar los diagnósticos pulpares utilizando tanto el oxímetro como las pruebas de frío u oxímetro y calor para detectar una pulpa sana; o pruebas de frío y eléctricas para definir pulpa enferma.
Subject(s)
Humans , Male , Female , Adolescent , Adult , Middle Aged , Young Adult , Dental Pulp/diagnostic imaging , Dental Pulp Diseases , Dental Pulp Test , Oximetry , Sensitivity and Specificity , Cold Temperature , Hot TemperatureABSTRACT
Abstract: The aim of this study was to investigate the effects of different post space irrigation protocols for removing residual filling material from dentin walls, by using microcomputed tomography (micro-CT), and the influence of these protocols on dentin microhardness. Bovine incisors (n = 35) were filled with the single-cone technique and MTA Fillapex (Angelus, Londrina, PR, Brazil). Post space preparation (PSP) was performed 7 days after filling, using the Odous Touch electrical system (Odous De Deus Ind. e Com., Belo Horizonte, MG, Brazil), followed by post space irrigation using manual irrigation, passive ultrasonic irrigation, or Easy Clean, together with 2.5% sodium hypochlorite (NaOCl), or with 2.5% NaOCl and 17% EDTA (NaOCl/EDTA). Micro-CT scans were performed at three time points. The residual filling material was evaluated at three levels: cervical, middle and apical. The Knoop test was measured with four indentations around the canal lumen at three dentin depths: X (100 μm), Y (200 μm) and Z (400 μm). Statistical analysis was performed using ANOVA (p < 0.05). The effects of the activation method (p < 0.001), and the root level (p = 0.013), as well as the interaction between the irrigant and the activation method (p = 0.041), led to different percentages of residual filling material. Lower amounts of residual filling material were observed at the cervical versus the middle and apical levels (p < 0.05). No significant differences were observed in dentin microhardness (p > 0.05). The best removal of the residual filling material was performed using the Easy Clean tip and NaOCl/EDTA, regardless of the activation methods.
ABSTRACT
Abstract The presence of residues within the root canal after post-space preparation can influence the bond strength between resin cement and root dentin when using fiberglass posts (FGPs). Currently, there is no consensus in the literature regarding what is the best solution for the removal of debris after post-space preparation. This systematic review involved "in vitro" studies to investigate if cleaning methods of the root canal after post-space preparation can increase the retention of FGPs evaluated by the push-out test. Searches were carried out in PubMed (MEDLINE) and Scopus databases up to July2017. English language studies published from 2007 to July 2017 were selected. 475 studies were found, and 9 were included in this review. Information from the 9 studies were collected regarding the number of samples, storage method after extraction, root canal preparation, method of post-space preparation, endodontic sealer, resin cement, cleaning methods after post-space and presence of irrigant activation. Five studies presented the best results for the association of sodium hypochlorite (NaOCl) and ethylenediamine tetra-acetic acid (EDTA), while in the other 4 studies, the solutions that showed improved retention of FGPs were photon-induced photoacoustic streaming (PIPS), Qmix, Sikko and EDTA. The results showed heterogeneity in all comparisons due to a high variety of information about cleaning methods, different concentrations, application time, type of adhesive system and resin cements used. In conclusion, this review suggests that the use of NaOCl/EDTA results in the retention of FGPs and may thus be recommended as a post-space cleaning method influencing the luting procedure.